Updated Nov 21, 2026· 10 min read

Key takeaways

  • Compare landmine attachments by bar fit, handle build and rotation, with the check-your-sleeve-size rule and plate-loaded-slowly habit for safer lifts.

A landmine turns one end of a barbell into a floor pivot. The fixed end sits in a base, the free end takes plates, and the bar swings in an arc that suits rows, single-arm presses, squats, deadlift variations and rotational core work. It is one of the smallest-footprint ways to add a whole movement family to a home gym, because the bar and plates you already own do most of the work.

Our top pick: Yes4All Landmine Attachment. Runner-up: Yes4All T-Bar Row Plate Post Insert with Double D Handle (Base and Handle).

The gear splits into two halves, and this guide covers both. The pivot base is the anchor: a plate-post insert, a bolt-down platform, or a rack-mounted post that holds the bar end and lets it swivel. The handle is what your hands hold at the lifting end: a Double D row handle, a Viking press frame with several grip positions, or a revolving grappler whose grips turn as you move. Each pick below is labeled plainly as a base or a handle, because buying one half when you needed the other is the most common mistake in this class. A complete setup needs one of each, unless a pick bundles both.

Disclosure: As an Amazon Associate, I earn from qualifying purchases. Product details were verified at the time of writing.

How to Choose a Landmine Attachment

Check your sleeve size first. This is the headline rule of the whole class. Standard bars have a 1 inch sleeve diameter and Olympic bars have a 2 inch sleeve diameter, and a landmine tube cut for one will not hold the other with any security. Measure the sleeve of the bar you will actually use before ordering anything. Some bases carry two tube sizes and accept both; most handles are cut for 2 inch Olympic bars only.

Pick the base format that matches your floor. A plate-post insert drops through the center holes of plates stacked on the ground, so the plates themselves anchor it and nothing is fixed in place. A bolt-down platform is the steadier choice for a permanent corner: it can be fixed to the floor or a wall, or clamped to a rack leg on some models. A rack-mounted post pins to an upright and uses the rack’s own mass, but those mounts are cut for one maker’s rack family, so the fit list matters more than the steel.

Look for a full swivel. A good pivot turns a full 360 degrees, so the bar can travel up, down and side to side through presses and rotations instead of fighting a fixed groove. On handles, the same idea shows up as revolving grips that rotate in your hands during a row or press, which keeps wrists in a neutral line as the arc changes.

Match the handle to the movement. A Double D handle is the rowing tool: two close grips for T-bar rows and corner rows. A Viking press frame gives wide, neutral grips for overhead and incline pressing, with enough space between the handles for your head. A revolving grappler sits between the two, turning landmine work into a grip that can roll through rows, presses and squat variations.

Read load numbers as maker figures. Every load number in this guide is the figure the maker publishes for that piece, stated plainly. Treat it as a ceiling to stay well under, not a target, and remember the pivot and the handle each carry their own figure — the lower of the two governs the setup.

The 5 Best Landmine Attachments

1. Yes4All Landmine Attachment — T-Bar Row Platform (Base)

This is the pivot base most home gyms should begin with. It is a compact steel platform with two tube sizes, so the small tube takes a 1 inch standard bar and the big tube takes a 2 inch Olympic bar — one of the few bases that covers a mixed bar collection without an adapter hunt. The joint swivels a full 360 degrees, and the plate can be bolted to the floor or a wall, or clamped against a 2×2 rack leg, so it can live permanently in a corner without becoming a trip hazard. The E-coated finish shrugs off garage humidity and chalk dust. It is a base only: you still need a handle for rows, which is the honest trade for a base this flexible.

Specs

  • Format: pivot base / platform
  • Bar fit: 1 inch standard and 2 inch Olympic bars
  • Rotation: 360 degree swivel joint
  • Build: alloy steel, E-coated finish
  • Sleeve length: 6.02 inches
  • Maker load figure: 880 lb
  • Part: LPL6
  • ASIN: B01077P1W2

2. Yes4All T-Bar Row Plate Post Insert with Double D Handle (Base and Handle)

This pick bundles both halves in one box. The base is a steel post that drops through the center holes of weight plates stacked on the floor — the plates anchor it, nothing bolts down, and the whole setup packs away when the session ends. The bar end slides into the insert’s sleeve and a lock knob firms it in place. A chrome Double D handle is included for the lifting end, with a diamond knurl texture across the grips, so rows can begin the day it arrives. The maker’s figure for the insert is lower than the bolt-down platform above, which fits its portable role: this is the format for lifters who train in a shared space and cannot fix anything to the floor.

Specs

  • Format: plate-post insert base, Double D handle included
  • Bar fit: 2 inch Olympic bars, adapters for 1 inch bars
  • Rotation: 360 degree swivel
  • Handle: Double D, 7.5 x 6.5 x 5.5 inches, chrome, diamond knurl grips
  • Build: alloy steel
  • Maker load figure: 400 lb
  • Model: YLTL
  • ASIN: B079M5FTM3

3. Yes4All Viking Press Handle (Handle)

The Viking press is the pressing specialist. Its frame slides over a 2 inch Olympic bar end and locks with a tightening knob, then offers three grip positions so the same handle covers neutral-grip overhead presses, incline presses and squat-to-press work. The handles sit 15 inches apart, a wider gap than most, which keeps your head clear of the frame at the top of a press. Heavy-gauge steel and a black paint finish keep it looking tidy in a garage. It is a handle only — it needs a pivot base at the other end of the bar — and it is the pick for anyone whose landmine work leans toward pressing rather than rowing.

Specs

  • Format: handle (Viking press frame)
  • Bar fit: 2 inch Olympic bars
  • Tube length: 7 inches
  • Grip positions: 3
  • Handle spacing: 15 inches
  • Build: alloy steel, black paint finish
  • Maker load figure: 300 lb
  • Model: MMSX
  • ASIN: B07YXMP152

4. Yes4All Landmine Double D Row Handle — Diamond Knurled (Handle)

If rows are the main event, this is the simple, direct tool. The Double D handle slides onto a 2 inch Olympic bar end, a tightening screw locks it, and the two diamond-knurled steel grips put your hands in a close, neutral position for T-bar rows and corner rows. Knurling is the detail that matters here: it holds its bite when palms sweat in a way smooth or coated grips do not, set after set. There is nothing to adjust and nothing to assemble, and its small size means it stores in a drawer between sessions. Pair it with any base in this guide — it is a handle only, and the maker’s load figure is the lowest of the five, so keep it for rowing loads rather than maximal deadlift variations.

Specs

  • Format: handle (Double D row handle)
  • Bar fit: 2 inch Olympic bars
  • Grip: diamond knurled steel handles
  • Fitting: slide-in sleeve with tightening screw
  • Build: alloy steel
  • Maker load figure: 250 lb
  • Model: FLKJ
  • ASIN: B086YKSRNY

5. Yes4All Revolving Grappler Handle (Handle)

The grappler is the most versatile handle of the five. Its two grips revolve through a full 360 degrees as you move, so the handle rolls with the arc of a row, a press or a squat instead of twisting your wrists against a fixed grip. That rotation is what opens up the movement list: single-arm rows feel smoother at the shoulder, and rotational presses can turn through the lift. The grips are knurled, the frame is alloy steel, and at just under 15 lb the handle itself has real heft, which steadies it on the bar. It fits 2 inch barbells and is a handle only, so it still needs a pivot base at the anchored end.

Specs

  • Format: handle (revolving grappler)
  • Bar fit: 2 inch barbells
  • Rotation: grips revolve a full 360 degrees
  • Grip: knurled
  • Build: alloy steel
  • Item weight: 14.52 lb
  • Maker load figure: 300 lb
  • Model: TG22
  • ASIN: B0BKL55L9R

Safety Notes

Anchor the base before you load the bar. A plate-post insert needs enough plate mass on the floor to hold it, and a bolt-down platform needs its fixings fully tight. An unanchored base can walk across the floor mid-set, and a walking pivot changes the bar path without warning.

Load plates slowly, and collar the bar end. Add plates one at a time on the lifting end, then fit a collar so the stack cannot creep outward as the bar arcs. A collar is a small habit that prevents the loudest failure in landmine training — plates sliding off a tilted bar.

Check the knob, pin and sleeve before every session. The tightening knob on a handle and the lock knob on a base are the two parts that take repeated stress. Back them off, look for cracked threads or a bent pin, and re-seat them by hand. A handle that rotates even slightly on the bar under load should be retired from heavy work until it holds firm again.

Begin lighter than you think. The arc of a landmine lift shifts load through the movement, and the bottom of a landmine squat or press feels different from the same plates on a straight bar. Build the first two weeks at loads you can pause at any point, and keep the maker’s figure for your weakest piece — base or handle — as the ceiling for the whole setup.

FAQ

Do I need both a base and a handle?
Yes, unless the pick bundles both, like the plate-post insert above. The base anchors one end of the bar; the handle gives your hands a proper grip at the other. A bar end alone can be gripped for some lifts, but rows and presses are safer and stronger with a handle made for the job.

Will these fit my standard 1 inch bar?
Only the picks that say so. The platform base takes both 1 inch and 2 inch bars, and the plate-post insert carries adapters for 1 inch bars. The three standalone handles are cut for 2 inch Olympic bars. Measure your sleeve before ordering — this is the check that prevents nearly every return in this class.

Can a landmine replace a rack for squats and presses?
It covers a useful slice of both: landmine squats, hack-style squats, single-arm presses and Viking presses all train hard without a rack. It does not replace a rack for barbell back squats or bench work. Think of it as a second training station built from a bar you already own.

How much floor space does a landmine setup need?
Roughly the length of your bar plus room to stand at the lifting end. The bases here are compact — a platform tucks into a corner and a plate-post insert stores with the plates — so a single garage bay corner is enough for most home gyms.

What is the difference between a Double D handle and a grappler?
A Double D handle is fixed: two grips in one close position, built for rows. A grappler’s grips revolve, so the handle can turn through rows, presses and squats. Fixed grips feel more locked-in for heavy rowing; revolving grips are kinder to wrists across a wider movement list.

Verdict

Begin with the base. The Yes4All platform is the most flexible anchor here — two bar sizes, a full swivel, and three ways to fix it down — while the plate-post insert bundle suits anyone who cannot bolt anything to the floor and wants a handle in the same box. For the lifting end, choose by movement: the Double D handle for rows, the Viking press frame for overhead work, and the revolving grappler if you want one handle that turns through all of it. Whichever pairing you build, measure your bar sleeve first, anchor the base, load the bar slowly with a collar on, and the landmine will earn its corner.

A
admin@88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Landmine Attachments for Rows, Presses and SquatsCheck price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.